Cooper-instruments-systems DFI INFINITY Digital Force Indicator/Controller Manual de usuario Pagina 57
- Pagina / 81
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Figure 10-4. High Deviation for both Active Above and Active Below
Figure 10-5. Low Deviation for both Active Above and Active Below
Figure 10-6. Band Deviation for both Active Above and Active Below
10.5 Selecting AL CNF Alarm Configuration Features
These bits offer the same selections for “SP 3” and “SP 4” as “SP CNF” did for “SP 1” and “SP 2”, except for the
last bit, which controls “SP 3” and “SP 4” LATCH reset.
1.“ALC.1=0” makes Alarm 1 (Setpoint 3) active above the Setpoint value.
“ALC.1=1” makes Alarm 1 (Setpoint 3) active below the Setpoint value.
When Alarm 1 (Setpoint 3) is assigned to place a band about the Setpoint 1 level (by setting “ALF.1=3”, described
in Section 10.6), “ALC.1=0” makes Alarm 1 (Setpoint 3) active ABOVE and BELOW the band (OUTSIDE the band),
with the chosen hysteresis for Alarm 1 (Setpoint 3) now inside the band. If “ALC.1=1”, Alarm 1 (Setpoint 3) is active
INSIDE the band, with the chosen hysteresis for Alarm 1 (Setpoint 3) now outside the band.
Figure 10-7 Illustrates the Alarm configuration for hysteresis.
CF 67 52 M1291/N/0403 11279ML-02 Rev. A
- DFI INFINITY 1
- STRAIN METER/CONTROLLER 1
- USER’S GUIDE 1
- CONTENTS 2
- NOTES, WARNINGS AND CAUTIONS 6
- 1.0 INTRODUCTION 6
- 2.0 UNPACKING 7
- 3.0 SAFETY CONSIDERATIONS 8
- 4.0 PARTS OF THE METER 9
- 4.2 Rear Of The Meter 11
- 5.0 SETUP 12
- 5.2.4 How To Access Jumpers 15
- installed 17
- 5.2.5 Panel Mount Assembly 18
- 6.0 JUMPER POSITIONS 20
- 7.1 Introduction 23
- 7.2 Signal Input Connections 23
- 7.3 AC Wiring Connection 25
- 8.1 Introduction 26
- 8.4.2 Scaling Your Meter 32
- 9.2 Meter Function Menus 39
- 9.2.1 INPUT 39
- 9.2.6 DEC PT (Decimal Point) 43
- 9.2.7 CNT BY (Count By) 43
- 9.2.18 BAUD (Baud Rate) 50
- 9.2.21 DAT FT (Data Format) 51
- 9.2.22 BUS FT (Bus Format) 52
- 9.2.23 SERCNT (Serial Count) 53
- 10.0 SETPOINTS/ALARMS 54
- 10.1 Features Overview 55
- 10.2 Unlocking The Features 55
- 12.0 ANALOG OUTPUT OPTION 60
- 12.1 Features Overview 61
- 12.2 Unlocking 61
- 13.0 BCD OPTION 63
- 13.2 BCD Card Jumper Table 64
- 13.3 Interconnect Board 64
- 14. RELAY OPTIONS 66
- 14.2 Wiring/Connections 68
- 15.1 Features Overview 69
- 16.0 EXTERNAL CONTROL LINES 70
- 17.2 Troubleshooting Guide 74
- 18.0 SPECIFICATIONS 75
- 19.0 FACTORY PRESET VALUES 78
- WARRANTY REPAIR POLICY 81
Relacionado con productos y manuales para Instrumentos de medición Cooper-instruments-systems DFI INFINITY Digital Force Indicator/Controller
Instrumentos de medición Cooper-instruments-systems DFI INFINITY Digital Force Indicator/Controller Manual de usuario
(78 paginas)
(78 paginas)
Instrumentos de medición Cooper-instruments-systems DFI Infinity CS Economy Digital Indicator Manual de usuario
(36 paginas)
(36 paginas)
Instrumentos de medición Cooper-instruments-systems AP 30001 Mechanical Crane Scale Manual de usuario
(1 paginas)
(1 paginas)
Instrumentos de medición Cooper-instruments-systems PS Mechanical Force Gages Manual de usuario
(6 paginas)
(6 paginas)
Instrumentos de medición Cooper-instruments-systems XST Tension Only Mechanical Force Gage Manual de usuario
(5 paginas)
(5 paginas)
Instrumentos de medición Cooper-instruments-systems Model 3i Basic Force/Torque Indicator Manual de usuario
(24 paginas)
(24 paginas)
Instrumentos de medición Cooper-instruments-systems Model 5i Advanced Force/Torque Indicator Manual de usuario
(35 paginas)
(35 paginas)
Instrumentos de medición Cooper-instruments-systems Series M2 Digital Force Gage Manual de usuario
(17 paginas)
(17 paginas)
Instrumentos de medición Cooper-instruments-systems Model 7i Professional Force/Torque Indicator Manual de usuario
(42 paginas)
(42 paginas)
Instrumentos de medición Cooper-instruments-systems Series M4 Digital Force Gage Manual de usuario
(23 paginas)
(23 paginas)
Instrumentos de medición Cooper-instruments-systems Series M3 Digital Force Gage Manual de usuario
(23 paginas)
(23 paginas)
Instrumentos de medición Cooper-instruments-systems M5-1000 High Capacity Digital Force Gage Manual de usuario
(28 paginas)
(28 paginas)
Instrumentos de medición Cooper-instruments-systems Series M7 Professional Digital Force Gauge Manual de usuario
(41 paginas)
(41 paginas)
Instrumentos de medición Cooper-instruments-systems TSFM 500 Motorized Force Test Stand Manual de usuario
(7 paginas)
(7 paginas)
Daikin CTXS35K2V1B manuales
Manuales del propietario y guías del usuario para Acondicionadores de aire del sistema de división Daikin CTXS35K2V1B.
Ofrecemos 2 manuales en pdf Daikin CTXS35K2V1B para descargar gratis por tipos de documentos: Manual de usuario, Manual de instalación
Comentarios a estos manuales