Cooper-instruments-systems DFI INFINITY Digital Force Indicator/Controller Manual de usuario Pagina 20
- Pagina / 81
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
The meter display should light, and pass through “RESET 2” to run or display mode. If the meter flashes an
overscale or overload message, press the ‘MENU’ button to advance to the configuration mode. Do not be
concerned about overloads (the +S input can stand 120 V continuously and current inputs can handle ten times
rated current).
6.0 JUMPER POSITIONS
6.1 Introduction
This section is for the configuration and setup of your jumper positions for readrate, unipolar or bipolar signal input,
sensor input signal jumpers, sensor excitation jumpers, pushbutton lockouts and lockout of lockout configuration
menus.
6.2 S1 Jumper Positions For Readrate And Unipolar Or Bipolar Input(S)
The typical readrate for your meter is 3/per second. This requires that no jumper has been installed in the S1A
position and Input Configuration (“IN CNF”) bit “INP.2” has been set to equal “0”. Your meter is capable of a fast
readrate of 13/per second. This requires that you install a jumper in the S1A position and the Input Configuration
(“IN CNF”) bit “INP.2” has been set to equal “1”. Refer to Figure 6-1 for the location of the S1 jumpers.
The typical setting for your meter is unipolar. For unipolar input, no jumper is installed in the S2B position and Input
Configuration (“IN CNF”) bit “INP.3” must be set to equal “0”. For bipolar inputs, install a jumper in S1B and set
Input Configuration (“IN CNF”) bit “INP.3” to equal “1”.
6.3 S2 Jumper Positions For Input Ranges
The following are the input signal jumper positions required to be installed in the “S2” position on your meter for the
current or voltage input ranges you require. These jumper positions include those that are required for sensor
excitation. Jumpers S2-N & S2-T are for either 1.5 to 11 Vdc or 24 Vdc sensor excitation. To select desired
excitation see Section 6.4. Refer to Figure 6-1 for the location of the S2 jumpers.
Figure 6-1. S1 and S2 Jumper Locations on Signal Input Board
BRIDGE – UNIPOLAR
Jumpers for 0 to 100 mV range: (meter supplied excitation)
Jumpers for 0 to 1 V range: (meter supplied excitation)
CF 67 15 M1291/N/0403 11279ML-02 Rev. A
- DFI INFINITY 1
- STRAIN METER/CONTROLLER 1
- USER’S GUIDE 1
- CONTENTS 2
- NOTES, WARNINGS AND CAUTIONS 6
- 1.0 INTRODUCTION 6
- 2.0 UNPACKING 7
- 3.0 SAFETY CONSIDERATIONS 8
- 4.0 PARTS OF THE METER 9
- 4.2 Rear Of The Meter 11
- 5.0 SETUP 12
- 5.2.4 How To Access Jumpers 15
- installed 17
- 5.2.5 Panel Mount Assembly 18
- 6.0 JUMPER POSITIONS 20
- 7.1 Introduction 23
- 7.2 Signal Input Connections 23
- 7.3 AC Wiring Connection 25
- 8.1 Introduction 26
- 8.4.2 Scaling Your Meter 32
- 9.2 Meter Function Menus 39
- 9.2.1 INPUT 39
- 9.2.6 DEC PT (Decimal Point) 43
- 9.2.7 CNT BY (Count By) 43
- 9.2.18 BAUD (Baud Rate) 50
- 9.2.21 DAT FT (Data Format) 51
- 9.2.22 BUS FT (Bus Format) 52
- 9.2.23 SERCNT (Serial Count) 53
- 10.0 SETPOINTS/ALARMS 54
- 10.1 Features Overview 55
- 10.2 Unlocking The Features 55
- 12.0 ANALOG OUTPUT OPTION 60
- 12.1 Features Overview 61
- 12.2 Unlocking 61
- 13.0 BCD OPTION 63
- 13.2 BCD Card Jumper Table 64
- 13.3 Interconnect Board 64
- 14. RELAY OPTIONS 66
- 14.2 Wiring/Connections 68
- 15.1 Features Overview 69
- 16.0 EXTERNAL CONTROL LINES 70
- 17.2 Troubleshooting Guide 74
- 18.0 SPECIFICATIONS 75
- 19.0 FACTORY PRESET VALUES 78
- WARRANTY REPAIR POLICY 81
Relacionado con productos y manuales para Instrumentos de medición Cooper-instruments-systems DFI INFINITY Digital Force Indicator/Controller
Instrumentos de medición Cooper-instruments-systems DFI INFINITY Digital Force Indicator/Controller Manual de usuario
(78 paginas)
(78 paginas)
Instrumentos de medición Cooper-instruments-systems DFI Infinity CS Economy Digital Indicator Manual de usuario
(36 paginas)
(36 paginas)
Instrumentos de medición Cooper-instruments-systems AP 30001 Mechanical Crane Scale Manual de usuario
(1 paginas)
(1 paginas)
Instrumentos de medición Cooper-instruments-systems PS Mechanical Force Gages Manual de usuario
(6 paginas)
(6 paginas)
Instrumentos de medición Cooper-instruments-systems XST Tension Only Mechanical Force Gage Manual de usuario
(5 paginas)
(5 paginas)
Instrumentos de medición Cooper-instruments-systems Model 3i Basic Force/Torque Indicator Manual de usuario
(24 paginas)
(24 paginas)
Instrumentos de medición Cooper-instruments-systems Model 5i Advanced Force/Torque Indicator Manual de usuario
(35 paginas)
(35 paginas)
Instrumentos de medición Cooper-instruments-systems Series M2 Digital Force Gage Manual de usuario
(17 paginas)
(17 paginas)
Instrumentos de medición Cooper-instruments-systems Model 7i Professional Force/Torque Indicator Manual de usuario
(42 paginas)
(42 paginas)
Instrumentos de medición Cooper-instruments-systems Series M4 Digital Force Gage Manual de usuario
(23 paginas)
(23 paginas)
Instrumentos de medición Cooper-instruments-systems Series M3 Digital Force Gage Manual de usuario
(23 paginas)
(23 paginas)
Instrumentos de medición Cooper-instruments-systems M5-1000 High Capacity Digital Force Gage Manual de usuario
(28 paginas)
(28 paginas)
Instrumentos de medición Cooper-instruments-systems Series M7 Professional Digital Force Gauge Manual de usuario
(41 paginas)
(41 paginas)
Instrumentos de medición Cooper-instruments-systems TSFM 500 Motorized Force Test Stand Manual de usuario
(7 paginas)
(7 paginas)
Daikin CTXS35K2V1B manuales
Manuales del propietario y guías del usuario para Acondicionadores de aire del sistema de división Daikin CTXS35K2V1B.
Ofrecemos 2 manuales en pdf Daikin CTXS35K2V1B para descargar gratis por tipos de documentos: Manual de usuario, Manual de instalación
Comentarios a estos manuales